Custom Front Seat Installation All Vehicles

Watch this guide to learn how to install your set of custom front seat covers!

Transcript

Introduction (0:05)

We’re going to show you how to install on this Wrangler SUV.

Slip on the console cover and seat bottom (0:08)

The first step is we’re going to slip on the center console cover. Then we are going to slip on the bottom set of the seat cover while also pushing the buckles down the crease.

Push the cover over the seat adjuster (0:19)

After that, we’re going to push the seat cover over the seat adjuster, and for any tucking like this, we recommend using the orange tucking tool.

Tie the bungee cord and buckle the bottom (0:28)

Then we’re going to grab the small bungee cord and tie it to the one on the other side. Then we can grab the buckles that we pushed through the crease and buckle them on the bottom. Then we are going to cinch them tight to the seat.

Repeat on the passenger seat (0:41)

We’re going to repeat this process on the passenger seat as well.

Slide on the top and zip it closed (0:46)

Then we’re going to slide the top of the seat cover onto the seat. We’ll then make sure that the seat covers are tightly secured to the holes that hold the headrest, and then we’ll pull the material together and zip it up at the bottom. After that, we can push down the flaps under the crease.

Reattach the headrest and cover (1:01)

We are now ready to put the headrest back on and then add the cover over top. Make sure to tuck any flaps underneath the headrest.

Repeat on the passenger side (1:11)

Now do the same thing you just did, but on the passenger side, and you’re done with your installation.

Support (1:17)

If you have any additional questions, feel free to reach out at info@seatcoversolutions.com.

Custom Back Seat Installation Truck

Watch this to learn how to install your custom back seat covers for a truck!

Transcript

Introduction (0:05)

We’re going to show you guys how to install back seat custom seat covers on this truck right here.

Install the bottom bench and push buckles through (0:10)

We’re first going to put the double seat bottom bench on. Then we’re going to grab the buckles and push them through the crease of the seat, and you’ll do the same to the buckles in the middle.

Buckle the bench from underneath (0:20)

Then we’re going to lift the bottom bench and grab the buckles from underneath. Then you’re going to put the buckle through the loop and attach it to the other side, and make sure to cinch it tight. Then you’re going to want to do the same to the two other buckles.

Hook the elastic bands and tuck the cover (0:36)

Then you’re going to grab the elastic bands on both sides and hook them on the buckle on either side. Then we’ll use the orange tucking tool to push down any excess seat cover. Once this is done, we’ll do the same exact thing to the other side.

Add the headrest and middle bench cover (0:49)

Then we’ll remove the headrest and add the seat cover over top. Then we’ll grab the bands and push them through the back of the seat. Then we will put the seat cover over the headrest holes. We recommend using the orange tucking tool for the easiest install.

Tuck the cover around the seat belt (1:05)

When putting the seat cover on the middle bench, make sure to go under the seat belt and tuck any excess seat cover in the crease.

Feed the seat belts and flap through the crease (1:12)

Now we can grab the seat belts and push them through the seat cover hole. Then we’ll push the bottom of the seat cover flap through the crease of the seat. Then we’ll do the same to the middle seat.

Buckle the bottom and middle seat (1:24)

Now we can grab the buckle and attach it to the bottom of the seat cover, making sure to cinch them tight. Once that’s done, we can do the same to the middle seat buckle.

Repeat on the other seat (1:34)

And now we will repeat that same exact process on the other seat.

Add the headrest cover and finish (1:40)

Last but not least, we’ll grab our headrest, put it back on the seat, and slip on the headrest cover. Then do the same to the other side, and you’re finished.

Support (1:53)

If you have any other questions, feel free to reach out at info@seatcoversolutions.com.

Custom Back Seat Installation Sedan

Watch this to learn how to install your custom back seat covers for a sedan!

Transcript

Introduction (0:05)

We’re going to show you how to install the back seat on this sedan.

Lay the bottom piece and push buckles through (0:09)

First, we’ll start by laying the bottom piece over the seat. Then we’ll push the buckles through the crease, and you’ll do the same on the other side.

Pull the straps tight and attach the buckle (0:16)

Then we’ll make sure everything is tight and that the seat belts come through the holes. Then we’ll pull the straps through and attach them to the buckle on the other side. Once that’s attached, you can cinch it tight and do the same on the other side.

Slip on the top cover (0:30)

Then we’ll slip on the top set of the seat cover. Make sure that the seat belt is on the outside of the seat cover, and then pull down on the back of the seat cover.

Push the flaps into the crease (0:39)

Now we can push the flaps on the bottom of the seat cover into the crease, and then you can pull it through from behind the seat.

Velcro the top to the bottom and zip it closed (0:45)

Now we can Velcro the top part of the seat cover to the bottom. Once that’s done, you can zip up the back of the seat cover. Then we’ll be doing the same exact thing on the other side.

Support (0:54)

If you have any other questions, feel free to reach out at info@seatcoversolutions.com.

Custom Back Seat Installation SUV

Watch this to learn how to install your custom set of back seat covers for a SUV!

Transcript

Introduction (0:05)

We’re going to show you how to install on this Wrangler SUV.

Slip the backrest over the headrest hole (0:08)

First, you’re going to want to grab your rear seat backrest. Then you’re going to want to slip the headrest through the hole built in the top. As you put it over the middle seat, make sure to grab the seat belt and pull it over the seat cover.

Lower the seat and secure the cup holder (0:22)

Then you can put the seat down and slip the ends over the edges of the seats. Make sure to pull out the middle seat cup holder, and then make sure everything is tight and snug.

Velcro the strap and thread the cover under the seat (0:30)

Then you can pull the strap through the headrest and Velcro it to the top of the seat cover. Then you’re going to thread the bottom of the seat cover under the seat. Then you’re going to do the same for the left side of the seat.

Lower the seat and zip it closed (0:45)

Then go ahead and lower the top of the seat again. Make sure to pull the material together, and then zip it up.

Attach the strap under the seat (0:53)

Then we’re going to pull the straps from under the seat. First, pull off the strap attached to the Velcro and attach them to the Velcro on the back of the [unclear: “cat”] cover.

Velcro the strap to the cup holder cover (1:05)

Then, back on the front side, make sure you push the Velcro strap under the cup holder, and once you get it through, Velcro it to the top of the [unclear: “cat”] cover.

Repeat on the single seat (1:17)

Repeat the same process for the single seat on the right side.

Slip on the headrest covers (1:23)

Then you can grab the headrest seat covers and slip them on, but make sure they are tucked and snug under the headrest.

Secure the middle cup holder cover (1:32)

Then pull off the Velcro strap on the middle seat cup holder cover, push it on securely, and make sure that the hole is on the top side. Then we will tuck the flaps under the holes where the headrest lies.

Tuck the strap under the cup holder (1:44)

Then, once again, we’re tucking the strap under the cup holder so that we can Velcro it on the other side.

Slip the middle headrest through the prongs (1:52)

Then slip the middle headrest through the two prongs. Then put the headrest back on the seat and pull it over the [unclear] of the headrest.

Install the bottom seat cover (1:59)

Now, to install the bottom seat covers, we’ll just slip it on and push the cover inside the crease.

Push the buckles through the crease (2:08)

Now we’re going to grab the buckles and push them down the crease of the seat, and do the same for the middle seat.

Buckle and cinch from the back (2:18)

Now go to the back of the seat and pull the straps through. Once you see the straps, you can now attach them to the buckles and then cinch each buckle tight.

Repeat on the single seat and finish (2:32)

Then we’re going to do the same thing on the other side for the single seat. Then grab the small bungee cord and attach it to the bottom of the seat, and then you’re done with your installation.

Support (2:41)

If you run into any problems along the way, feel free to email us at info@seatcoversolutions.com.

Frequently Asked Questions

What do I do if I am having fitment issues?

If you are having issues with the way your seat covers fit. Please email us a picture of the issues you are having as well as a description of the problem. We have installation technicians on standby waiting to help you with any questions you may have about the fitment.

What do I do if have received the wrong product?

If you have received the wrong product, please email us a picture of the product you received as well as the product you ordered. If possible, please provide your name and order number as well. This will ensure that you get the correct product sent out right away.

Will I still be able to use my cup holder/armrest in the back seat?

Yes, our seat covers are designed to accommodate your car's existing cup holders and armrests. With our custom line, each set will have a cutout made that allows you to access your cup holder/ armrest in the back seat!

Am I able to get my center console covered?

It is in between universal and custom. There are 2 different sizes of the body of the front seat, 6 different sizes of headrests, and 2 different sizes of the back seat. As long as your vehicle is compatible with the website, you can expect the same fit as advertised in our Facebook, Instagram, and TikTok videos. Check those out @seatcoversolutions.